Precision Air Services Plc wishes to invite applications from suitably
qualified candidates to fill in this challenging position.
POSITION: QUALITY ASSURANCE INSPECTOR – TRAINEE (1 POSITION)
REPORTS TO: QUALITY ASSURANCE MANAGER
DUTY STATION: DAR ES SALAAM
ROLE PURPOSE OF THE STATEMENT:
Perform continuous surveillance to technical activities,
processes and systems to ensure compliance with TCAA and Precision Air
standards for safe and efficient maintenance of aircraft, components and
equipment for optimum airline operations.
KEY ACCOUNTABILITIES/RESPONSBILITIES:
The recruited candidate will undergo training to qualify and
be assigned job functions in the Quality Assurance division which includes the
following duties:-
Responsible to the Manager Quality Engineering for: -
Random checks on the Hangar, Line Maintenance and Workshops
for adherence to the laid down procedures and standards.
·
Ensures that inspections
performed on airframe, engines and components are in accordance with Company
Policies and procedures, maintenance manuals and approved technical data
·
Monitors workmanship and
materials to verify that the Company and TCAA rules, regulations, and standards
are complied with.
·
Ensures that receiving
inspections of incoming parts, components, equipment supplies and materials is
completed in accordance with the Company Maintenance Procedures Manual (MPM).
·
Ensure assistance in the
classification of repairs and alterations in relation to Major or Minor
Repairs. Ensure appropriate forms are completed to document any major repair or
alteration.
·
Monitors/audits aircraft
inspection reports, log pages and records for accuracy and completeness of
entries prior to being sent to the Aircraft Records Department.
·
Conducts daily audits of
aircraft work packages including checks/inspections forms, log pages, routines
and non-routines, modification orders, etc. to ensure completion, correctness,
use of appropriate references to approved data in all entries and forms.
·
Monitors the safety and
housekeeping of the work areas.
·
Interact with Technical
Records Sections with regards to aircraft records compliance.
·
Participating in periodic
audit of all Technical Divisions and outstations and daily audit of maintenance
paperwork generated in the Hangar and Line maintenance. Ensuring accomplishment
of all these inspection duties within scheduled time, without compromising
safety.
·
Responsible of inspection
duties in the Hangar, Line Maintenance and stores.
·
Ensuring proper recording
and certification of all maintenance activities on the Aircraft.
·
Ensuring high standard of
Airworthiness is maintained in all Precision Air Aircraft.
·
Ensuring use of appropriate
tools, equipment, manuals, Techniques and methods for Inspection and
maintenance of Aircraft.
·
Ensuring duplicate
Inspection on Engines and flight controls is carried out at the base.
·
Ensuring that maintenance
work is performed in accordance with the standards and procedures of the
Approved Maintenance Schedule.
·
Ensuring Approved
Maintenance Schedules, comply with the applicable TCARs, TCAA requirements, and
directives from Foreign Airworthiness Authorities if they are applicable to
Precision Air Aircraft.
·
Ensuring issuance of Release
Certificates (CRS) after Hangar checks and ensuring that all C of A documents
are on board the Aircraft before final release to service.
·
Ensuring all components and
equipments are properly labelled
·
Ensuring proper inspection
coverage in areas where airworthiness may be affected such as fuel tanks,
compliance with MODs, ADs or SBs, structural repairs, corrosion control, power
plant installation, flight control surfaces installation, duplicate inspection,
landing gear retraction checks and Engine ground runs.
·
Participation in Auditing
work being done on Aircraft during Hangar checks and ensuring that work is
completed and paper work promptly signed and certified soon after each task has
been completed.
·
Participation in Engine
ground runs, observing and recording of all Engine parameters.
·
Ensuring Engine run and
component change sheets are available and are appropriately signed and
certified after completion of each task.
·
Ensuring final walk around
checks are performed and all mandatory documents are valid and on board prior
to releasing the Aircraft for service.
·
Ensure all the maintenance
manuals are updated.
·
Enforcing company and
Regulations requirements which relate to Airworthiness of Aircraft.
·
Responsible as reference to
Safety Management Manual [SMM] Doc ref. PW/CM/002 Chapter 1.6.2[i]-[vii].
PERFORMANCE INDICATORS:
Inspection feedbacks
Completed work-pack audits
Incidents/discrepancies
Audit frequency
Audits from regulatory authorities
Multiple type licenses/ approvals
COMPETENCIES:
Sensitive to details
Observant
Ethical
Independent minded
Organized
Precise and conservative
Effective communicator
Team player
Safety conscious
Knowledge seeking
Must be able to multi-task
MINIMUM QUALIFICATIONS:
Diploma/FTC in either Mechanical, Aeronautical, Electrical,
Electronics or Telecommunications.
Engineering degree and aircraft engineering background
would be an added advantage.
Broad overview of the maintenance system
Computer literate, must be proficient in Microsoft Windows/Microsoft
Office (Word & Excel) and internet.
Must have good verbal and written communication skills.
Company Indoctrination, MPM training required
Must receive General Familiarization Training on all
airframe operated by the company.
Closing Date:
Not later than 20th February 2017
Mode of Application:
If you feel you meet the above requirements please send your
application and CV to the address below. Only short‐listed applicants will be contacted.
Director of Human Resources and Administration
Precision Air Services Plc
Mail Box 70770
Dar es Salaam
TANZANIA.
E‐mail: pwrecruit@precisionairtz.com
jmarealle@precisionairtz.com
2 Comments
Just have to thank you for this great information. This is what I was looking for (Thanks Bing supplier management company in china
ReplyDeleteReally appreciate you sharing this blog post.Thanks Again. Awesome. composites
ReplyDelete